In common with the rest of Yemen there was a period of building with concrete frame and concrete blocks-introduced 40 to 50 years ago-thought to be quicker and cheaper to build but also seen as the modern way and as its done in the West.
An existing patio has flag stones set over a concrete slab. If you were to remove the flag stones and thinset, what would be the best way to raise the level of the existing slab to make up for the
To connect the base plate of the wall to the concrete youÂd need to use an expansion type anchor. There are a couple of variations Â a wedge type and a sleeve type but they all do the same thing Â expand in the hole to make a secure connection to the concrete.
Overpouring Old Concrete with New Concrete. Step 3: Stake 2*4 forms flush against the sides of the concrete slabs, 1" to 2" above the concrete surface make sure height is even . Drive stakes every 3 ft. and at every joint in the forms. Mark control joint locations onto the outside of the forms, directly above existing control joints.
Click on this link if you're looking for more information about garage remodeling, home construction and building repairs.
Re: Existing concrete patio Jim. I had considered that but the problem was that to get the concrete up to the underside, I would have to set my forms outside enough to get concrete in and higher than the underside elevation. This will create a visible ledge and will make the foot print larger.
Concrete stains offer limited color choices, are often unpredictable and are difficult to work with. Concrete dyes offer the ease of application of concrete paint with the durability of concrete stain in a wide variety of colors. Concrete dyes are perfect for coloring an existing concrete slab.
It's not unlike refinishing hardwood floors. Ensure floor is suitable for polishing. Sources I've seen state that nearly any concrete floor can be polished, so long as it is structurally sound. Floors that are very porous, need extensive patching, or are wavy are probably not good candidates. New slabs need to cure for 28 days before polishing.
Concrete may be tough as rock, but with the right tools, securing walls to slabs is a smooth process. With simple materials and readily available tools, the novice carpenter can lay out, build and anchor walls on concrete slabs.
how to build a deck over an existing concrete patio. How to build a deck over an existing patio slab with low clearance. Even if we removed the austere concrete slab how to build a deck over existing concrete ..>> how to build a deck on existing slab - Wood Plastic Composite outdoor floor
It is possible that you may have to remove the existing slab, prepare the supporting subbase properly, and then pour a new slab to achieve the results you desire. You'll find a lot of useful information in two ACI reports: "Concrete Repair Guide," ACI 546, and "Guide for Concrete Floor and Slab Construction," ACI 302.1.
how to build a deck with exiting concrete floor. to level out existing wood or concrete floors in order to install hardwood floors, carpet, How to Build a deck over a concrete stoop with This Old House - Similar to How to Build a deck over a concrete stoop with This Old House Jun 10, 2008 How to Build a deck over a concrete stoop with This Old House .
Part 1: Prepping for Pouring Concrete Part 2: Pouring a Concrete Slab As concrete specialist Phil Truit oversees the pouring of a concrete slab floor into the basement of an existing home the
Make 24-inch marks along the sleepers at each side of the floor, from end to end. Snap chalk lines on the sleepers between the corresponding marks as reference lines for the floor joists that
How to build and extend an existing Block Wall Odell Complete Concrete. How to TOP DRESS your lawn to make a FLAT LEVEL surface How to Build A Concrete Block Wall - Duration:
To install them, a hole is drilled, and the anchor is driven into the hole until it is flush with the concrete. Then, a special setting tool is used to expand the anchor. This anchor is used in light to heavy duty applications. Bolts must be spaced along the floor or wall to distribute the load that will be attached.
Pouring a Concrete Floor in a Post Frame Building. Best product to use is A2V reflective insulation. Unroll reflective insulation over prepared site sand or gravel, with aluminum side facing ground white side up . Overlap by 2 at seams. Run reflective insulation up skirt board inside by 6.
The main problem with trying to frame a shed on an existing concrete slab is trying to set the sill plate. The actual framing follows a standard process, the only exception being that you may have to toe-nail to attach the studs.
Allow the floor to dry. Pour primer onto your clean dry floor, and use a soft-bristle push broom to spread it over the entire surface of the floor, pushing down to get it into the pores of the concrete. Sweep of any excess puddles of primer, you want to end up with a smooth concrete surface.
My thought: to build forms and, using the preexisting anchor bolts extended by a connector, and pour concrete into the forms thus raising the foundation in preparation for an actual floor. Please let me know.
1 Cut a Concrete Floor for New Plumbing; Measure from the tip of the bit and make a reference mark 1 1/2-inch from the end. William. "How to Install a Toilet on an Existing Slab." Home
Cinder blocks are a great tool for building garden walls or storage structures in your yard. Any structure that you build will be more stable when it is set on a solid foundation. If the area where you are planning to use the cinder blocks is already covered with a concrete pad, you can easily build a cinder block wall right on top of the concrete.
weather resistant wooden planks>how to build a deck with exiting concrete floor Egypt PRODUCTS Our company is focused on the product quality management, fully complementing the environmental protection awareness, and it's among the first companies in this
Step 8. Empty the contents of the large bucket onto the concrete patio, starting at both corners of the sloping end. Allow the leveling compound to flow and level itself for one to three minutes, or until it stops. Use the flat side of a metal trowel to feather the edges of the leveling compound flush with the rest of the patio.
Then, build a perimeter, or a wood brace, that is the same height as you want to concrete to be. Make sure the braces are level, and lay down a barrier of wire mesh over the existing concrete inside of the barrier. Pour and spread a thin later of scratch coat, and then add a bond layer on top of the coat.
Two other considerations a vapor barrier under the new/top slab to stop moisture from impregnating the concrete from underneath, freezing-expanding and eventually cracking your slab. this can be as simple as a sheet of 6mil polyvinyl. A sealer on top of the cured floor again to stop moisture from impregnating the floor.
Make the mixture slightly stiffer drier than normal concrete. Spread the concrete, then press down on the concrete with 2*4 or shovel to pack the mixture into the forms. Smooth the surface with a screed board. Calculate how much material you will need with the concrete calculator. Step 6: Float the concrete with a wood float, then tool with