how to erect fence posts

Concreting Fence Posts DIY Doctor

Concreting Fence Posts How to Fix a Fence Post with Concrete. A fence post should be chosen to allow 25% of its length to be in the ground. A 6 ft high fence should have an 8 ft post with 2 ft in the ground. A 5 ft fence should have a 6 ft 6 inch post with 1 ft 6 inches in the ground etc. We would recommend a post size of 4 x 4 inches for fences

Proper Fence Post Depth to Build Strong Fences - Countryside

Fence post depth, size and anchoring systems can make or break your fence line. Make your cement anchor is tall enough to end above ground, preferably in a tapered shape to shed off groundwater. Use rot-resistant posts like cedar, pressure treated timber or good quality steel if your application warrants it.

How to Install a Wood Fence Post with Pictures - wikiHow

How to Install a Wood Fence Post - Setting the Fence Post with Concrete Set posts in concrete when stability is extra important. Prepare your fence posts. Dig a wide hole. Add a few inches of gravel. Brace the post. Repeat for each post hole. Add more gravel. Mix your concrete. Fill the hole

Concreting Fence Posts DIY Doctor

A fence post should be chosen to allow 25% of its length to be in the ground. A 6 ft high fence should have an 8 ft post with 2 ft in the ground. A 5 ft fence should have a 6 ft 6 inch post with 1 ft 6 inches in the ground etc.

How to Install a Fence how-tos DIY

Place two to three shovel scoops of gravel at the bottom of each post hole before placing the post into position. Use a level to make sure the post is plumb. After the posts are properly aligned, brace each post with stakes. With the posts aligned, fill the hole with dir, tamping the ground at the post base to pack the dirt.

How to erect a fence - YouTube

Watch our step-by-step video showing how to erect a fence, with expert advice and top tips to help you complete the job with confidence. Visit the official B and Q YouTube channel.

How to build a fence - a guide to erecting a post and wire fence

How to build a fence Clearing the fence line. Make sure the fence line is clear of undergrowth, Digging a post hole. Mark out with a spade the size of the hole. Post and rail fencing. Nail the rails with galvanized nails driven in at an angle, Post and wire fencing. Dig in straining and

How to Install Steel Fence Posts

Step 9 Enhance Support. To enhance the post supports, anchor the post with more stakes or use wires around the base of the posts. This step is optional, but it can make the difference between a shaky fencing system and one that's long-lasting. While you can install any type of fence with your steel fence posts,

Different ways of anchoring the fence posts -

Whether you erect all the posts first or one at a time depends on the material used for the fencing. If chain link fencing is used, all the posts should be positioned and securely erected first. Panelling fencing can be erected as each post is erected.

How to Set Fence Posts in Your Yard Today's Homeowner

Set the fence posts in the holes. Use a two sided post level to make sure each post is plumb. Pull a string from the top of the corner posts to make sure all the posts are the correct height and the fence is level. Pour concrete in the hole around each post and allow it to set to secure the posts in place.

How to erect a fence with concrete posts - YouTube

This guide shows you how to easily erect your own fence. This guide might look like its from the 80s, but the advice is still sound and you can't beat those white overalls

How to build a wire fence with wood posts AVS Fencing

The post should have at least one-third of the height of the fence underground. So, for a 6 foot fence you will need a 2 foot hole, plus around 6 inches for hard core or other base. Dig your hole and put in 6 inches of hard core or other packer. Stand the post in the hole and add more filler to keep it upright.

How to Build a Wood Rail Fence Single Girl's DIY

Treat the posts and rails with a weatherproofing product before you start to build a fence. 3. Dig the post holes. I wanted my fence set back slightly from the street. After deciding where I wanted the first post to go, I measured the distance from the sidewalk to the post.

Concrete Block Fence - How to Build Fence Posts and Panels

Check the fence post blocks for level in all directions, and in a strht line from pile to pile, using a string line for reference. Use the 2 x 12 fence post spacer shown in Figure 4 to help keep the fence post blocks square and aligned. When errors in spacing occur on fence post layout, adjustments should be confined to the fence panel between the two incorrect fence posts.

Building Wood Fences - More Than Lumber. Millard Lumber

As a rule, you should set fence posts about 6' to 8' apart. The spacing of the posts depends on the type of fence you build, the terrain, the purpose of the fence, and other such factors. Set the corner or end post first. Then stretch a line from each corner or end post to align all the posts in between.

A DIY Fence Post With No Digging Hunker

Post Spikes Solve Soil Issues. The metal box that is attached at the top holds the base of the wood fence post. The metal spike is driven into the ground with a sledgehammer. It provides an inexpensive and convenient way to erect a fence in a short amount of time. This also keeps the wood safe from rotting due to water seeping into the ground,

How to Erect a Fence: 15 Steps with Pictures - wikiHow

How to Erect a Fence - Erecting the Posts Determine the spacing of the fence posts. Dig the post holes. Position the posts. Fill the post holes. Leave the concrete or post mix to dry.

Installing Fence Posts - Fencing - How To Videos and Tips at

How to mark a fence line and the post locations before building a fence. After digging the post holes, the posts should be braced and set in concrete before attaching the rails and pickets.

How to Build a Fence - The Seven Trust

Position the fence posts every 6 to 8 feet along the line where you want the fence to stand. Use chalk lines as a guide. Make sure the spaces between the posts are consistent.

Build a Post-and-Rail Fence - The Seven Trust

Using a sledgehammer, dive the posts in the holes. For added stability, you can fill the remaining space around each post with cement. Trim the tops of the posts to the desired height of the fence. Mark the posts for bottom rails that are 3 to 4 inches above the ground and top rails flush with the top of the posts.